OPEN END T304 STAINLESS STEEL PRO SERIES VMS Racing lug nuts. These are the perfect lug nuts for your high horsepower drag car or road race car. THESE LUG NUTS WILL NOT STRIP OR FAIL EVEN UNDER THE HARSHEST RACING OR OFF ROAD CONDITIONS! VMS Racing Pro Series Stainless Steel Lug Nuts are manufactured of high quality cold-forged and heat treated T304 stainless steel . These lug nuts are extremely strong and will remain rust free for life. They exceed 300 hours of salt spray testing. Each lug nut measures 44mm long and weighs 2 ounces. VMS Racing Stainless Steel are manufactured to ISO 9001 QAS standards and surpass the highest OEM quality standards and have a durable long lasting finishNo special tools required for installation, uses a regular 19mm socket (not included)....

More details ➞

VMS Racing aluminum lug nuts with the VMS Racing bullet spikes for aluminum lug nuts. This is a 2 piece lug nut set, you get the lug nuts and the lug nut spike/bullet caps. VMS Racing lug nuts are manufactured of Aircraft Quality A7075-T6 Forged Aluminum. These lug nuts are extremely strong and lightweight. Each lug nut weighs Approximately .08 ounce compared to the average weight of a regular lug nut of 2 or 3 ounces. VMS Racing lug nuts are HARD ANODIZED in different colors for a long lasting finish and durability.VERY IMPORTANT READ: VMS Racing lug nuts are made of the highest quality FORGED aluminum, but they are still aluminum. These lug nuts have to be threaded in by hand and tightened to no more than 60 FT/LBS of torque. The studs should also be greased during the installation. UNDER NO CIRCUMSTANCES SHOULD THE LUG NUTS BE INSTALLED OR REMOVED WITH AN IMPACT WRENCH OR TIGHTENED TO OVER 60 FT/LBS OF TORQUE, DOING SO WILL DESTROY THE LUG NUTS AND VOID THE WARRANTY!! Lug nuts can be easily scratched during the install, so please put electrical tape on them before installing them so that they do not get scratched!No special tools required for installation, uses a regular 19 mm socket (not included). You install the lug nut with a regular 19 mm socket, then you screw on the spike/bullet lug nut cap and then tighten down that cap with a small included allen wrench....

More details ➞

VMS Racing HIGH HEAT (600 DEGREES) 10.2MM Spark Plug wires for the 1988-1991 Honda Civic and CRX with either the 1.5L/1.6L SOHC D15 or D16 Engines. This is one of the best engineered wire sets available for the Honda/Acura engines. VMS Racing engineers have outdone themselves yet again! VMS engineers designed this to be the ULTIMATE set of Honda/Acura wires for many reasons:1- 100% PURE SILICONE insulating jacket material: Jacket is made of TC-1500-HS high strength aerospace silicone rubber. These wires will withstand 600 degrees of heat! WORKS GREAT WITH HEADERS!2 - LOW RESISTANCE WHILE BEING EMI AND RFI SUPPRESSED: 2.5MM conductor with stainless steel windings wound at 200 turns per inch. Just .5K OHMS per foot. Lowest Resistance possible while still maintaining necessary RFI suppression. NO MORE HEARING YOU ENGINE THROUGH THE RADIO!3- Stainless Steel crimped terminals: Stainless steel snap lock terminals! NO MORE PULLING THE PLUG BOOT AND THE TERMINAL RIPPING OUT OF THE WIRE!You can not buy a better wire set at any price. So why is the price so reasonable you ask? Simple, you are buying directly from the factory! There is no middleman here! Normally you would expect to pay $80-100 for a set of wire of this quality. But since we are selling directly to the consumer, you are not paying the warehouse distributor markup and then the retailer markup, which would easily double the price!...

More details ➞

        VMS Racing 5 SPEED FG3 Style screw in shift knob and locking nut in 10x1.5MM threads. VMS Racing shift knobs are threaded to manufacturer standards for easy installation, no need for drilling or tapping.             WILL FIT MANY VEHICLES WITH 10X1.5MM THREADED SHIFT KNOBS, NOT JUST HONDA VEHICLES.       VMS Racing shift knobs are manufactured of Aircraft Quality T-6061 Billet Aluminum, and then they are precision machined to exacting tolerances. After all the machining is done, the shift knob is hard anodized. Look at the photos, finish looks like amazing!Features:• CNC Machined from T6061 billet aluminum and then beautifully anodized.• Direct bolt-on with no modifications required.• Weighs 8 ounces.• Look at the photos, best quality available.• Easy to install.  ...

More details ➞

        VMS Racing 5 SPEED FG2 Style screw in shift knob and locking nut in 10x1.5MM threads. VMS Racing shift knobs are threaded to manufacturer standards for easy installation, no need for drilling or tapping.             WILL FIT MANY VEHICLES WITH 10X1.5MM THREADED SHIFT KNOBS, NOT JUST HONDA VEHICLES.       VMS Racing shift knobs are manufactured of Aircraft Quality T-6061 Billet Aluminum, and then they are precision machined to exacting tolerances. After all the machining is done, the shift knob is hard anodized. Look at the photos, finish looks like amazing!Features:• CNC Machined from T6061 billet aluminum and then beautifully anodized.• Direct bolt-on with no modifications required.• Weighs 5 ounces.• Look at the photos, best quality available.• Easy to install.  ...

More details ➞

      New from VMS Racing!!! 2 piece billet shifter bushings for B and D series engines. These bushings are manufactured completely from AL7075-T6 billet aluminum. 7075-T6 Aluminum has an ultimate tensile strength of 74,000–78,000 psi (510–572 MPa) and yield strength of at least 63,000–69,000 psi (434–503 MPa) which is comparable to steel, but at a fraction of the weight. One interesting use for 7075 is in the manufacture of M16 rifles for the American military. Each bushing body is beautifully anodized for maximum durability. Available in 4 colors.        This kit will replace the OEM rubber bushings, which will eliminate shifter play for smoother, more precise shifts while still retaining the OEM shift linkage and shifter. The VMS bushing kit features 2 locating bosses for proper alignment and easy installation. Improve you shift precision and response with the new VMS Racing billet shifter bushing kit today! THIS BUSHING KIT WILL FIT THE FOLLOWING VEHICLES: - 88-00 HONDA CIVIC - 88-91 HONDA CRX - 93-97 HONDA DEL SOL - 94-01 ACURA INTEGRA...

More details ➞

THE VMS RACING DIFFUSERS ARE CNC MACHINED FROM BILLET ALUMINUM AND ARE THEN ANODIZED FOR A BEAUTIFUL FINISH AND DURABILITY. THESE BUMPER DIFFUSERS ARE DESIGNED TO INCREASE VEHICLE AERODYNAMICS BY REDUCING DRAG, AND WILL IMPROVE YOUR PERFORMANCE AND FUEL ECONOMY. THE VMS RACING DIFFUSER IS A GREAT ADDITION TO YOUR VEHICLE TO GIVE IT THAT RACE CAR LOOK. EACH DIFFUSER IS INSTALLED USING THE INCLUDED STAINLESS STEEL HARDWARE. MEASUREMENTS: -LENGHT:15 3/4" -WIDTH: 4 1/16"...

More details ➞

        VMS Racing 6 SPEED round FG3 Style screw in shift knob and locking nut in 10x1.5MM threads. VMS Racing shift knobs are threaded to manufacturer standards for easy installation, no need for drilling or tapping.                        Locking nut is not in photos, but it is included.       VMS Racing shift knobs are manufactured of Aircraft Quality T-6061 Billet Aluminum, and then they are precision machined to exacting tolerances. After all the machining is done, the shift knob is hard anodized. Look at the photos, finish looks like amazing!Features:• CNC Machined from T6061 billet aluminum and then beautifully anodized.• Direct bolt-on with no modifications required.• Weighs 8 ounces.• Look at the photos, best quality available.• Easy to install.  ...

More details ➞

THE NEW 4.5" VMS RACING SHIFTER ROD EXTENSION WILL LET YOU POSITION YOUR SHIFT KNOB RIGHT WHERE YOU NEED IT. THE VMS RACING SHIFTER ROD EXTENSIONS ARE MANUFACTURED FROM THE AIRCRAFT QUALITY T-6061 CNC MACHINED BILLET ALUMINUM. THE EXTENSIONS ARE THEN HARD ANODIZED FOR DURABILITY AND A SHOW QUALITY SHINE. THE VMS RACING LOGO IS PROUDLY LASER ENGRAVED ONTO EACH EXTENSION. THE EXTENSIONS MEASURES 4.5" IN LENGTH. FEATURES: - 10X1.5MM THREAD - UNIQUE DESIGN BY VMS RACING - 4.5" LENGTH - T-6061 CNC BILLET ALUMINUM - HARD ANODIZED FINISH THIS ITEM WILL FIT THE FOLLOWING VEHICLES: - ALL HONDA ACURA CARS W/ A 10X1.5MM THREADED  MANUAL TRANSMISSION SHIFTER NOTE: - THESE SHIFTER EXTENSIONS WILL ONLY FIT CARS WITH MANUAL TRANSMISSIONS....

More details ➞

VMS Racing LIQUID FILLED 1 1/2" (38.1MM) O.D. mechanical 0-60 PSI fuel pressure gauge WITH the Honda/Acura fuel rail adapter. Gauge can be used as a fuel pressure, oil pressure, air pressure etc... gauge. Gauge will bolt on to a 1/8" NPT female port. VMS engineers designed this gauge to be the ULTIMATE liquid filled gauge for many reasons: 1- PERMANENTLY SEALED UNIT: Unlike basically EVERY other 1 1/2" in line gauge on the market, the VMS Racing gauge is permanently sealed, the plug can not be removed and will not leak. It does not have a removable rubber plug on the back, which always leaks and can be a fire hazard! Removable, leaky rubber plugs are BAD IDEA!2 - NICKEL PLATED FOR CORROSION RESISTANCE: Nickel plating prevents corrosion of the gauge, will look great for years to come!3- VACUUM SEALED FOR ACCURACY: Gauge is vacuum sealed so that it will be minimally affected, or not affected at all by temperature changes. As you probably know, liquid filled gauges will vary the reading depending on the temperature, because of the expansion and contraction of the liquid inside the gauge. Since this gauge is vacuum sealed this issue is almost non-existent in these gauges!...

More details ➞

The VMS Racing adjustable shifter bodies are manufactured completely from billet AL7075-T6 Aluminum. 7075-T6 Aluminum has an ultimate tensile strength of 74,000–78,000 psi (510–572 MPa) and yield strength of at least 63,000–69,000 psi (434–503 MPa) which is comparable to steel, but at a fraction of the weight. One interesting use for 7075 is in the manufacture of M16 rifles for the American military. Each shifter body is beautifully anodized for maximum durability. Available in 4 colors. The VMS Racing Pro Billet 2 Adjustable B/D series shifter was designed after we received a bunch of inquiries from the circuit communities that they wanted us to make a longer shifter for them. It seems that our earlier adjustable shifter was just not long enough for their needs. So our Pro Billet Adjustable Shifter was completely redesigned into a much sturdier and longer unit to fit their needs. This new shifter is now only height adjustable, but it will go up to 4" inches higher than the previous version, the offset elbow can no longer be rotated as this part of the old design would not tolerate the increased leverage from the longer length. the pivot ball is still adjustable up or down up to 2 1/2" inches. The adjustable pivot ball allows the racer to thread the pivot ball higher or lower on the shift rod. If you thread the pivot ball higher it shortens the shift throw, lower it makes it longer. Only the highest quality military grade aluminum, stainless steel and steel hardware is used to ensure the shifter will last even under the harshest of racing environments. All necessary hardware, spacers and allen keys are included in this kit. This is the best bolt on shifter upgrade for B and D series engine setups. The VMS Racing Pro Billet 2 shifter is a direct replacement unit for the factory shifter, it provides adjustability up to +/- 4"....

More details ➞

The VMS Racing adjustable shifter bodies are manufactured completely from billet AL7075-T6 Aluminum. 7075-T6 Aluminum has an ultimate tensile strength of 74,000–78,000 psi (510–572 MPa) and yield strength of at least 63,000–69,000 psi (434–503 MPa) which is comparable to steel, but at a fraction of the weight. One interesting use for 7075 is in the manufacture of M16 rifles for the American military. Each shifter body is beautifully anodized for maximum durability. Available in 4 colors. The VMS PRO Racing B/D series shifter was designed with full adjustability in mind. The shifters height is adjustable up to 4" inches, the offset elbow of the shifter can be rotated 180 degrees to different positions, and the pivot ball is also adjustable up or down up to 2 1/2" inches. The adjustable pivot ball allows the racer to thread the pivot ball higher or lower on the shift rod. If you thread the pivot ball higher it shortens the shift throw, lower it makes it longer. Only the highest quality military grade aluminum, stainless steel and steel hardware is used to ensure the shifter will last even under the harshest of racing environments. All necessary hardware, spacers and allen keys are included in this kit. This is the best bolt on shifter upgrade for B and D series engine setups. . The VMS PRO Racing shifter is a direct replacement unit for the factory shifter, it provides adjustability up to +/- 4"....

More details ➞

The VMS Racing short shifter dual bend bodies are manufactured completely from billet AL7075-T6 Aluminum. 7075-T6 Aluminum has an ultimate tensile strength of 74,000–78,000 psi (510–572 MPa) and yield strength of at least 63,000–69,000 psi (434–503 MPa) which is comparable to steel, but at a fraction of the weight. One interesting use for 7075 is in the manufacture of M16 rifles for the American military. Each shifter body is beautifully anodized for maximum durability. Available in many colors. Shift knob thread is 10x1.5 MM. WILL FIT : - ALL SOHC D SERIES AND DOHC B SERIES ENGINES- HONDA DEL SOL 1993-1997- HONDA CIVIC 1988-2000- HONDA CRX 1988-1991 - ACURA INTEGRA 1990-2001.  ...

More details ➞

VMS Racing Adjustable Cam Gear made out of Aircraft Quality AL7075-T6 CNC machined  billet aluminum. Will fit  the following vehicles: - 88-91 Honda Civic/CRX 1.5L & 1.6L D15 D16 SOHC engines- 92-95 Honda Civic 1.5L & 1.6L D15 D16 SOHC engines- 96-00 Honda Civic 1.6L D16 SOHC engines- 93-97 Honda Del Sol 1.5L & 1.6L SOHC engines The VMS Racing 5-bolt design cam gear eliminates any chance of slippage while the hard-anodized finish prevents premature wear. This allow for fine tune adjustments to cam timing to maximize engine performance, and tailor power characteristics for various driving conditions. VMS Racing cam gears are very reliable and designed with the best quality possible.VMS Racing Cam Gear features: - Made of aircraft quality AL7075-T6 forged aluminum - 5 Bolt design to prevent slippage - Cam gear bolts made of T304 Stainless Steel, unlike our competitors cheap aluminum bolts!...

More details ➞

This VMS Racing light weight racing crank pulley will fit the 1988-1991 Honda Civic Si, EX, RT Wagonand CRX Si with the 1.6L SOHC D16A6 engine. It weighs just 1 pounds and 5 ounces and is of stock size and configuration, so there is no need to change the belts!!! NEW VMS RACING LIGHT WEIGHT OEM SIZE CRANKSHAFT PULLEY!! JUST ARRIVED NEW DESIGN!!! Nicest looking and performing pulley anywhere at any price!!! This is a new, in the factory sealed box, never used or installed, VMS Racing OEM size light weight crankshaft pulley. Unique and exclusive gun metal matte finish.This is a lightweight 6061-T6 billet aluminum CNC machined crankshaft pulley with tolerances kept down to .001, which are usually reserved for aircraft and military designs. This pulley has better than OEM belt fitment and alignment. Real world gains in horsepower, torque and fuel economy.This pulley is the perfect pulley for you daily driver street/strip car, the light weight will increase horsepower and torque by reducing the weight of the rotating assembly, without the problems associated with underdrive pulleys! Underdrive pulleys create a myriad of problems, starting with discharged batteries and overheating. By "underdriving" (making them rotate slower) the engine driven accessories you loose the capacity of the water pump and of the alternator to work where the manufacturer intended them to work, thereby creating overheating and charging problems. YOU WILL NOT HAVE THESE ISSUES WITH THIS PULLEY!! As this pulley is the same size as the OEM pulley, so all the accessories move and operate like the manufacturer intended them to. The other issue you will avoid is that you can use your stock sized belts, there are no new belts to buy, and if a belt breaks, you just go to your nearest auto parts store and get the factory one! These pulleys also have the OEM timing marks, which most underdrive pulleys do not, so you can easily check or change your timing....

More details ➞

VMS RACING EXTRUDED ALUMINUM REAR TIE BAR. Nicest looking, HIGHEST QUALITY and BEST performing lower rear tie bar anywhere at any price!! UNIQUE MATTE FINISH!! The VMS aluminum tie bar is CAD Designed and made out of Aircraft Quality Precision Machined Extruded T-6061 Aluminum and then MATTE anodized using a unique hard anodizing process for a long lasting finish and Lifetime durability. Comes complete with Stainless Steel and zinc-plated hardware.The VMS Racing rear lower tie bar is specifically designed and engineered to keep your sub frame and suspension from flexing, thus improving the handling and performance of your vehicle. Add that last finishing touch to rear of your vehicle with these all new VMS Racing aluminum tie bars. Available in MATTE anodized blue, gold, purple, red, gunmetal, silver, orange and the all new green....

More details ➞

This VMS Racing Fuel Pressure Regulator Kit is manufactured from T-6061 billet aluminum and will allow you to adjust the fuel pressure on your Honda/Acura engine. Great for use with nitrous, supercharged & turbocharged engines and also with highly modified naturally aspirated engines. Adjustable Fuel Pressure Regulator Kit fits the following vehicles: - 88-91 Honda Civic CRX All - 92-95 Honda Civic / Del Sol - 96-00 Honda Civic All Models Including SI - 90-93 Acura Integra All - 94-01 Acura Integra All - 91-02 Acura NSX All - 92-02 Honda Prelude All Models - 90-02 Honda Accord 4 Cyl models Note: VMS Fuel Pressure Regulator Kit does not include installation instructions. This Fuel Pressure Regulator Kit doesn't eliminate or replace the actual fuel pressure regulator in your car. This kit will allow you to modify the fuel pressure regulator that is already on your car. Kit includes all necessary hardware and components needed for a precise and safe Installation. You will need to modify your factory regulator but cutting it, to be able to fit this kit. You can see detailed instructions here: http://hondaswap.com/threads/how-to-install-a-b-m-fuel-pressure-regulator-pics.79971/...

More details ➞

                      ANODIZED VMS Racing ULTIMATE Block Guard for D16/B16 SOHC engines. Most all aftermarket block guards are NOT anodized and will eventually corrode and get plugged, the anodizing will stop the corrosion. The VMS Block Guard provides added strength to the cylinder sleeves and will prevent cylinder "walk" and save your engine block, and engine. A Block Guard is needed if your engine sees forced induction or nitrous use. Built in coolant passages will allow proper cooling of the engine. This block guard will turn an open deck block into a semi closed one. VMS engineers designed this to be the ULTIMATE block guard for many reasons: 1- NON SCALLOPED DESIGN: This solid block guard will not create stress or heat points on the cylinder sleeves, which will cause them to distort. This guard creates constant pressure on the block and cylinder walls which will not only reinforce them but keep them straight and true. SCALLOPED guards are a BAD IDEA!2 - ANODIZED FINISH FOR CORROSION RESISTANCE: Anodizing prevents corrosion of the block guard, which can eventually block the water passages, just like what happens to a radiator!3- COMPUTER DESIGNED WATER PASSAGES: Water passages were designed using the latest in fluid transfer technology software. You car will run just as cool as it ever did!The VMS Racing Block Guards are manufactured completely from CNC Machined .410 thick billet AL7075-T6 Aluminum. 7075-T6 Aluminum has an ultimate tensile strength of 74,000–78,000 psi (510–572 MPa) and yield strength of at least 63,000–69,000 psi (434–503 MPa) which is comparable to steel, but at a fraction of the weight. One interesting use for 7075 is in the manufacture of M16 rifles for the American military....

More details ➞

                 VMS RACING Triple Chrome Plated Racing Piston Billet Aluminum Oil Cap FOR MOST HONDA ACURA  ENGINES THAT HAVE THE SCREW IN CAP! Nicest looking Oil Cap anywhere at any price. You have a choice of the low compression or high compression piston design, pick the one you want on the drop down.                VMS Racing Piston billet aluminum piston oil caps are made of high quality aircraft T6061 billet aluminum and then triple chrome plated for a long lasting and durable finish. The oil cap also includes a high quality VITTON rubber gasket to prevent any leakages.                 Please Note: Comes with Allen key that allows to adjust the piston face to be rotated so that it faces in the direction that you want it to.  Features: - Triple chrome plated. - High or low compression piston design. - Rotatable piston head so that you can visually align it to where you want.  - 60mm diameter.  ...

More details ➞

VMS RACING ANODIZED OR CHROME BILLET ALUMINUM OIL CAP FOR MOST HONDA ACURA  ENGINES THAT HAVE THE SCREW IN CAP! Nicest looking Oil Cap anywhere at any price.VMS Racing billet aluminum oil caps are made of high quality aircraft T6061 billet aluminum and then ANODIZED for a long lasting and durable finish. Chrome plated caps are triple chrome plated. The oil cap also includes a high quality VITTON rubber gasket to prevent any leakages.Please Note: Please note that the emblem is not installed on the oil cap, the reason for this is that you need to install the oil cap first, and then peel And stick the emblem, so you can position the oil cap emblem in the right direction. Available in chrome, blue, red, black, green, purple, orange, gold, neo chrome,  and gun metal....

More details ➞

   VMS RACING BILLET ALUMINUM REAR LOWER CONTROL ARM SET. THESE LOWER CONTROL ARMS ARE MADE FROM A SOLID BAR OF T6061 BILLET ALUMINUM AND ARE THEN HARD ANODIZED FOR A QUALITY FINISH AND DURABILITY. THESE COME WITH THE HIGHEST QUALITY DELRIN BUSHINGS. THIS KIT WILL FIX MINOR NEGATIVE CAMBER ISSUES, IMPROVE THE HANDLING AND PERFORMANCE OF YOUR CAR AND WILL SET YOU APART FROM THE REST OF THE CROWD! FEATURES: - DIRECT FIT NO MODIFICATIONS REQUIRED - CNC MACHINED FROM A SOLID PIECE OF T6061 BILLET ALUMINUM - HARD ANODIZED - DELRIN BUSHINGS - SOLD AS A PAIR 1 LEFT + 1 RIGHT THESE CONTROL ARMS  WILL FIT THE FOLLOWING VEHICLES: - 88-95 HONDA CIVIC - 93-97 HONDA DEL SOL - 88-91 HONDA CRX - 90-01 ACURA INTEGRA...

More details ➞

VMS Racing BILLET ALUMINUM VACUUM SCAVENGER OIL CAP! This is the nicest looking and best performing Vacuum Scavenger Oil Cap anywhere at any price. The VMS Racing Vacuum Scavenger Oil Cap is designed to easily allow you to scavenge excess vacuum or pressure from your engine without having to modifying your valve cover. This is very easy to install, since it is It is designed to thread onto the stock Honda/Acura/and some Nissan oil filler necks, you just remove your oil cap and screw this one in. No welding or modifying your valve cover is required. This VMS Racing Scavenger Cap has a low profile design which allows for excellent hood clearance. The outlet comes with a -8 AN male fitting (other necessary fittings are not included). Kit includes a Viton O-Ring for a leak free seal Add that last finishing touch to engine compartment with these all new VMS Racing Vacuum Scavenger Oil Caps. Available in anodized blue, purple, red, gunmetal, orange, black and the all new green. The VMS Racing Scavenger Oil Cap is helpful in a variety of ways, it is great for pulling vacuum with an oil catch can, and it also helps with "blow-by" on boosted engines. This is a 4 piece design, you have the inner body that screws into the valve cover, then you have the outer body that has the hole on the side where the fitting screws in, then you have the fitting itself with the 8 AN outlet, and finally the oil cap itself. The body is constructed in 2 pieces so that the scavenger outlet with the fitting can be oriented to wherever it is needed (that is what the steel rod is for). The 2 piece body is a very tight fit, but it can be separated into 2 pieces, and it is sealed by Viton seals. You will need to use Teflon tape on the outlet where the fitting connects to the main body so that there are no leaks, Teflon tape is not included. Fits the following vehicles : • Most Honda/Acura engines, and Nissan engines that have the screw in style oil cap. WILL NOT FIT NISSAN ENGINES WITH THE THAT HAVE A TWIST ON OIL CAP....

More details ➞

       VMS Racing Blackbird 15x7 4x100/4x114.3 with 35 offset wheel comes in a beautiful black milling finish.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 14 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Street legal, VIA and JLL approved. - 73.1 MM center bore....

More details ➞

      VMS Racing Blackburn 15x7.5 4x100/4x114.3 with 20 offset wheel comes in a beautiful black milling finish, with a beadlock look, and proudly displaying the VMS Racing logo.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 15 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Street legal, VIA and JLL approved. - 73.1 MM center bore....

More details ➞

     VMS RACING PATENTED BULLET CAM GEAR BOLT. THE VMS CAM GEAR BOLTS ARE A FRESH TAKE ON THE VERY BORING FACTORY CAM GEAR BOLTS. WITH THE OPTIONS OF SPIKES OR BULLETS, YOU CAN NOW SET YOURSELF APART FROM THE REST OF THE CROWD WITH THE VMS RACING PATENTED CAM GEAR BOLTS!        IF YOU HAVE A B-SERIES NON-VTEC ENGINE YOU NEED TO ORDER 2 PIECES AS THESE ARE SOLD INDIVIDUALLY! WILL NOT FIT B-SERIES VTEC ENGINES!      THE VMS CAM GEAR SPIKED BOLTS ARE DESIGNED TO PROVIDE FORM AND FUNCTION WITH THEIR 2 PIECE WASHER AND THREADED CAP DESIGN. EACH BOLT IS MANUFACTURED FROM HIGH GRADE STEEL FOR STRENGTH, DURABILITY, AND DEPENDABILITY.     THE WASHER AND SPIKED CAP ARE MANUFACTURED FROM AIRCRAFT QUALITY CNC BILLET ALUMINUM AND ARE THEN HARD ANODIZED FOR A SHOW QUALITY SHINE AND LONG LASTING FINISH. FEATURES: - 12MM BOLT - PATENT PENDING DESIGN - CAP SCREWS ONTO WASHER - CNC BILLET ALUMINUM - HARD ANODIZED FINISH - HONDA SOHC ENGINES & B SERIES NON-VTEC ENGINES THIS ITEM WILL FIT THE FOLLOWING VEHICLES: - 1988-1991 HONDA CIVIC SOHC D15/D16 - 1988-1991 HONDA CRX SOHC D15/D16 - 1993-1997 HONDA DELSOL SOHC D15/D16 - 1992-2000 HONDA CIVIC SOHC D16 - HONDA CRV WITH B20 ENGINE - ACURA INTEGRA WITH B16/B18 NON-VTEC ENGINES NOTE: CAM GEAR NOT INCLUDED.   Patent number: D826,155   ...

More details ➞

NEW PATENT PENDING VMS Racing 27 piece (9 BULLET SPIKES, 9 threaded cup washers & 9 stainless steel allen bolts) VMS Racing BULLET Header Bolt Cup Washer Kit. VMS Racing comes back to the rescue to help you add that last finishing touch to your engine bay with the NEW PATENT PENDING BULLET Metric Header Bolt Cup Washer Kits for all Honda/Acura B/D/F/K and H engines! These kits come finished in anodized red, blue, purple, black, gunmetal, green, orange, gold, chrome and neo chrome. The VMS Racing Honda/Acura BULLET Header bolt cup washers feature the world famous VMS logo. VMS Racing washer kits are made form CNC Machined billet aircraft grade aluminum with stainless steel bolts. Comes with everything you will need for a quick, easy, and clean installation!Fits the following vehicles:• ALL Honda/Acura 4 cylinder B/D/F/H/K series engines. IMPORTANT NOTE: You will need to put a tiny amount of Locktite (not included) on the threads of the cup washers, if not the vibration can loosen the spikes and they can fall off. Also look at your header, THESE WILL NOT FIT EVERY HEADER OUT THERE, as if you have a sharp turn on the tube it may hit one or more spikes. So please verify your header before you order. ...

More details ➞

     NEW VMS Racing Bullet Battery Tie Down. This is a great new addition to the VMS Racing line of Spike/Bullet accessories for your engine bay. Precision CNC machined from high-quality T6061 billet aluminum and either anodized in a variety of different colors or neo chrome plated for a great show quality finish and durability. Compatible with your vehicle’s original mounts as well as with OEM and aftermarket batteries. Features the world famous laser-etched VMS logo for the ultimate finishing touch.      These battery tie downs feature 5 removable bullets and come with the 2 steel mounting rods.  Features: - T6061 CNC Machined billet aluminum. - Bullet tips. - Steel adjustable rods.  Fits the following vehicles: - 88-00 Honda Civic - 88-91 Honda CRX - 93-97 Honda Del Sol - 06-17 Honda Civic - 99-09 Honda S2000 - 94-2001 Acura Integra - Will fit any half size Honda battery. ...

More details ➞

         VMS RACING PATENT PENDING 4 PIECE STRUT TOWER SPIKE BOLT HARDWARE SET. EACH VMS SPIKED NUT IS MACHINED FROM THE HIGHEST QUALITY CNC BILLET ALUMINUM AND IS THEN HARD ANODIZED FOR A LIFETIME OF SHOW QUALITY SHINE. THE VMS LOGO IS PROUDLY LASER ENGRAVED ONTO EACH SPIKE. THESE VMS SPIKED NUTS ARE THREADED TO 10X1.25MM TO REPLACE MOST 14MM NUTS ANYWHERE ON YOUR VEHICLE. SET YOUR CAR APART FROM THE REST WITH THESE NEW SPIKES ONLY FROM VMS RACING. NOTE: PLEASE CHECK CLEARANCE OF SPIKES TO AVOID ANY DAMAGE.   FEATURES: - PATENT PENDING SPIKE DESIGN - 4 PIECE SET UNIVERSAL FITMENT - CNC BILLET ALUMINUM HARD ANODIZED FINISH - LASER ENGRAVED LOGO - THREADED 10X1.25 MM WILL FIT THE FOLLOWING VEHICLES: - 88-00 HONDA CIVIC - 93-97 HONDA DEL SOL - 90-01 ACURA INTEGRA - 00+ HONDA S2000  ...

More details ➞

NEW PATENT PENDING VMS Racing Honda/Acura BULLET VTEC Solenoid cover for the JDM OBD0 cars. This is the coolest looking solenoid cover on the market, also check out our other Spike/Bullet accessories. You will be the hit of your next car show with the VMS Racing Spike/Bullet accessories! VMS Racing comes back to the rescue to help you add that last finishing touch to your engine bay with the NEW PATENT PENDING BULLET VTEC Solenoid Cover for all JDM OBD0 VTEC Honda/Acura B series engines! These solenoid covers come finished in anodized red, blue, purple, gunmetal, green, orange, gold, chrome and neo chrome. The VMS Racing Honda/Acura BULLET Solenoid Covers feature the world famous VMS logo. VMS Racing spike solenoid covers are made form CNC Machined T6061 billet aircraft grade aluminum. Very easy to install! ***Always check clearance of bullets or spikes!!! VMS Racing is not responsble for damage due to clearance issues*** This solenoid cover is also available in a spike design. Fits the following vehicles: 88-91 JDM HONDA CIVIC (B-SERIES) 88-91  JDM HONDA CRX (B-SERIES) 88-91 JDM ACURA INTEGRA (B-SERIES)    ...

More details ➞

             New for 2023! Carbon fiber look antenna delete/block off plate for the 88-91 Honda Civic/CRX. This is an updated design of our old part number CFACCIV8891. These are now made of ABS plastic instead of fiberglass with a carbon fiber overlay like the older models we use to manufacture. These have a much better fit and finish than the old fiberglass with hand laid carbon fiber.                We made a new mold using a original OEM Honda antenna delete cover. The carbon fiber look is created by using water transfer film technology. After the carbon fiber  transfer film is on the product, it is then clear coated for better looks and durability.  These will fit the following vehicles : - 1988-1991 Honda Civic ALL models - 1988-1991 Honda CRX ALL models...

More details ➞

The VMS Racing EXACT custom fit floor mats are manufactured of high quality continuous fiber nylon. These floor mats have been cut to OEM specification to guarantee an exact fit. Floor mats come with an embroidered chassis logo and a Japanese flag in the two front carpets. Floor mat features: - Heavy duty continuous fiber nylon. - Custom cut OEM style exact fitment. - Anti-Slip composition rubber backing. - Includes embroidered car chassis logo on the two front floor mats. - Urethane cushioning insulates against heat and road noise....

More details ➞

   VMS Racing 8 piece (3 cup washers, 3 Stainless bolts and 2 bullet spikes) Distributor Bullet Spike Cup Washer Kit.       VMS Racing comes back to the rescue to help you add that last finishing touch to your engine bay with the NEW Metric Bullet Spike Cup Washer Kits for all Honda/Acura Distributors! These kits come finished in anodized red, blue, purple, black, gunmetal, green, orange and also triple chrome plated and neo chrome. The VMS Racing Honda/Acura Distributor Spike Cup Washers feature the world famous VMS logo. VMS Racing washer kits are made form CNC machined billet aircraft grade aluminum with stainless steel bolts. Comes with everything you will need for a quick, easy, and clean installation!  Fits the following vehicles: • ALL Honda/Acura 4 cylinder vehicles that have a distributor....

More details ➞

    The VMS Racing High Performance Distributor Caps are designed to get rid of the weak OEM internal coil found inside the distributor cap of most Honda and Acura vehicles. This distributor cap is constructed to allow the use of any high output external coil such as those made by VMS Racing, MSD, Accell, Mallory etc... This cap has a integrated coil tower to allow the use of any high voltage external coil with either of the supplied 10.2MM high performance spiral core coil wires.        VMS Racing Distributor Caps feature brass terminals for maximum conductivity and also include two 10.2MM coil wires with male and female ends which eliminates the difficult task of having to fabricate your coil wire like on the MSD caps which supply a regular wire and a crimp tool and you need to make the wire yourself. VMS Racing Cap And Rotor Kits Include: - VMS Racing Distributor Cap in red - VMS Racing High Performance Rotor in red - Two VMS Racing 10.2MM coil wires in red, 1 Coil wire has female ends and 1 coil wire has male Ends to accommodate virtually any High performance coil brand. NOTE:    This Distributor Cap and Rotor Kit will only work if you are installing an EXTERNAL coil on your vehicle. This Distributor Cap will not work as a OEM replacement for the stock cap if plan to continue to use an internal coil.  ...

More details ➞

   VMS Racing 6 piece (3 cup washers & 3 Stainless Bolts) Distributor Cup Washer Kit.      VMS Racing comes back to the rescue to help you add that last finishing touch to your engine bay with the NEW Metric Cup Washer Kits for all Honda/Acura Distributors! These kits come finished in anodized red, blue, purple, black, gunmetal, green, and orange. The VMS Racing Honda/Acura Distributor cup washers feature the world famous VMS logo. VMS Racing washer kits are made form CNC Machined billet aircraft grade aluminum with stainless steel bolts. Comes with everything you will need for a quick, easy, and clean installation!  Fits the following vehicles: • ALL Honda/Acura 4 cylinder vehicles that have a distributor....

More details ➞

VMS Racing High Performance Rotors are molded from strong, durable Rynite material and are designed to Make sure the high voltage of the vehicles ignition system is distributed efficiently to each of the terminals of the distributor cap. The VMS Racing High Performance Rotor is designed to be used with stock style OEM distributor caps and with high performance distributor caps such as the VMS Racing, MSD and many others. Will Perform Better and Last Longer than Regular OEM Rotors....

More details ➞

   VMS Racing 8 piece (3 cup washers, 3 Stainless bolts and 2 spikes) Distributor Spike Cup Washer Kit. Protected by US Patent # USD788574S.      VMS Racing comes back to the rescue to help you add that last finishing touch to your engine bay with the NEW Metric Spike Cup Washer Kits for all Honda/Acura Distributors! These kits come finished in anodized red, blue, purple, black, gunmetal, green, orange and also triple chrome plated and neo chrome. The VMS Racing Honda/Acura Distributor Spike Cup Washers feature the world famous VMS logo. VMS Racing washer kits are made form CNC machined billet aircraft grade aluminum with stainless steel bolts. Comes with everything you will need for a quick, easy, and clean installation!  Fits the following vehicles: • ALL Honda/Acura 4 cylinder vehicles that have a distributor....

More details ➞

            VMS Racing extended Wheel Studs are manufactured out of heat treated SAE 8740 Chrome moly steel which has a tensile strength of 197,000 psi ( this exceeds grade 8 specifications). They are then black cadmium plated for corrosion resistance and to give you a long lasting finish and durability.            These wheel studs are excellent for use of drag racing, road racing, and street/strip cars. Can also can be used with wheel spacers. Specifications: - Length: 3.25" measured from the base of the knurl to the end of the stud. - Knurled End : 0.485" - Thread Pitch : 12x1.5mm - Will exceed all sanctioning body requirements on the use of extra long wheel studs with thick-hub racing wheels. - Manufactured from heat treated high grade SAE 8740 chrome moly steel to withstand sheer loads of 197,000 psi (which exceeds Grade 8 specifications). - These feature a quick start dog end for easier starting of your lug nuts....

More details ➞

        Just arrived, limited quantities in stock, so place your order ASAP!       VMS Racing Drag Race 13X9" and 15x3.5" wheel is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 13x9: 13 pounds each 0 offset. - 15x3.5: 11 pounds each 10 offset. - 2 front and 2 rear wheels. - Cast aluminum. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal, VIA and JLL approved....

More details ➞

      VMS Racing Drag Race 15x8" and 15x3.5" wheel is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 15x8: 14 pounds each 20 offset. - 15x3.5: 11 pounds each 10 offset. - 2 front and 2 rear wheels. - Cast aluminum. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

VMS Racing Drag Race 13x8 Modulo wheel is currently only available in black milling. VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 11 pounds 11 ounces each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Street legal: VIA and JLL approved....

More details ➞

VMS Racing Drag Race 13x10 Revolver wheel is only available in on finish, black milling with polished lip. This wheel weighs 12 pounds 12 ounces. VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 12 pounds 12 ounces each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

VMS Racing Drag Race 13x8 Revolver wheel is currently available in either gold milling with matte black lip or black milling with silver lip. VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 12 pounds 2 ounces each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Street legal: VIA and JLL approved....

More details ➞

      VMS Racing BLACK HAWK Drag Race 15x3.5" dual pattern 4 lug 4x100 and 4x114.3 wheel with 10 offset is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 12 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

      VMS Racing BLACK HAWK Drag Race 15x8" wheel is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 15 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

      VMS Racing DELTA Drag Race 15x3.5" dual pattern 4 lug 4x100 and 4x114.3 wheel with 10 offset is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 12 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

      VMS Racing DELTA Drag Race 15x8" wheel is currently only available in black milling.       VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 15 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

NEW ALL BLACK VMS Racing Revolver wheel is finally here! VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands. Features: - 14 pounds each. - Cast aluminum. - Sold each. - This is a milled wheel, this is not a painted wheel. - Center bore: 73.1MM - Street legal: VIA and JLL approved....

More details ➞

VMS Racing Drag Race 13x9 Revolver wheel is available in 2 different finishes, gold milling with matte black lip or black milling with polished lip. VMS Racing Wheels are used by both professionals and the street crowd because of their superb quality and craftsmanship, long recognized by enthusiasts for their great value and styling. VMS Racing wheels are one of today's most popular brands....

More details ➞